SCB-100
Modular Systems > National Instruments > Accessories
Description: | SCB-100, 100 Pin, Female Screw Terminal, Shielded I/O Connector Block |
Need an Official Quote?
Or speak to a sales representative for additional information:
National Instruments SCB-100 Shielded Connector Block
The SCB-100 (Part Number: 776990-01, 182788C-01) is a Shielded Connector Block. This Connector Block is designed to provide easy cabling between 100-pin digital I/O devices and I/O signals. The NI SCB-100 offers maximum protection from noise corruption since it is a shielded accessory with a reference temperature sensor. It has 100 screw terminals, and a strain relief bar.
The following are needed to use the SCB-100:
· 100-pin DAQ device and device documentation,
· SH100100 cable for E Series/MIO devices or SH100-100-F cable for DIO/TIO Series devices,
· ≤26 AWG wire,
· And other equipment which can be found in the installation guide.
This Shielded Connector Block is designed for E Series MIO devices (NI 6025E, 6031E, 6071E and 6033E), DIO devices (NI 6511, 6508, PCI-DIO-96, 6509, 6512, 6514, 6513, 6527, 6515 etc.), and devices from the TIO Series like NI 6624. Moreover, the NI SCB-100 can be used with various other products that come with a 100-pin male 0.050 series shielded D-type I/O connector. The temperature sensor incorporated in this Connector Block can accommodate a broad range of thermocouple models. With the SCB-100, you can measure thermocouples in single-ended or differential configurations.
This National Instruments SCB-100 Shielded Connector Block offers low-noise signal termination when it is used with shielded cables. Low noise termination is important for digital signal transmission systems. The NI SCB-100 comes equipped with 3 general purpose breadboard areas. This Connector Block comes equipped with chassis ground terminals that can be used for grounding high-impedance sources. The cold-junction sensor can provide an output of 10 mV/°C with ±0.5 °C accuracy. In typical operating conditions, the NI SCB-100 should draw no more than 10 mA of current at +5 VDC. The NI device weighs 15.6 oz, and measures 7.7 x 6.0 x 1.8 in. in physical dimensions. The device has a component operating temperature range of 0 to 70 °C, a storage temperature range of –55 to 125 °C, and a noncondensing operating and storage humidity range of 5% to 90% and 5% to 90% respectively.
SCB-100 Obsolete Status has been announced by National Instruments, but the Connector Block will still be available for purchase and repairs by Apex Waves.
Model | SCB-100 |
---|---|
Manufacturer | National Instruments |
Part Number | 776990-01, 182788C-01 |
Type | Shielded Connector Block |
Screw Terminals | 101 |
Cold-Junction Sensor Accuracy | ±0.5 °C |
Cold-Junction Sensor Output | 10 mV/°C |
I/O Connectors | One 100-pin male 0.050 series shielded D-type connector |
Dimensions | 7.7 by 6.0 by 1.8 in. |
Weight | 1 lb 15.6 oz. |
Warranty | Three Year Warranty |
SCB-100 Manual | User Manual and Maintenance Manual Available for Download |
Price | Contact a sales representative for a quote. |
Associated part numbers for the SCB-100:
146521A-01L, 182788-01, 182788B-01, 182788C-01, 182788D-01, 182788E-01L, 182788F-01L, 182790-01, 182790A-01, 182790B-01, 182790C-01, 182790D-01L, 776990-01
Associated NSNs for the SCB-100:
7025-01-469-8205 (7025014698205), 7025-01-469-8205 (7025014698205)
National Instruments SCB-100 Frequently Asked Questions
Question: What are the switch settings for the SCB-100?
Answer: Before you can connect an IMAQ D100100 cable to an IMAQ SCB-100 connector block, the switch settings on the IMAQ SCB-100 must be changed to the generic screw terminals switch configuration.
Question: How many screw terminals does the SCB-100 use?
Answer: The SCB-100 has 101 screw terminals, including one no-connect terminal. There are all I/O signals available at the terminals.
Question: At what temperature should the SCB-100 component be operated?
Answer: The operating environment temperature of the SCB-100 ranges from 0 - 70 degrees celsius.
SCB-100 PDF Manuals
ARCHIVED IMAQ D100100 CABLE INSTALLATION GUIDE.PDF
ARCHIVED LOOKOUT 3.7 ADDENDUM.PDF
ARCHIVED LOOKOUT OBJECT REFERENCE MANUAL.PDF
ARCHIVED LOOKOUT REFERENCE MANUAL.PDF
IMAQ SCB-100 CONNECTOR BLOCK AND IMAQ D100100 CABLE.PDF
NI 60XX 60XXE PINOUT LABELS FOR THE SCB-100 NOTE TO USERS.PDF
NI 6528 6529 USER GUIDE AND SPECIFICATIONS.PDF
NI 65XX PINOUT LABELS FOR THE SCB-100 NOTE TO USERS.PDF
NI 6624 CALIBRATION PROCEDURE.PDF
NI 66XX PINOUT LABELS FOR THE SCB-100 NOTE TO USERS.PDF
NI USB 6509 USER GUIDE AND SPECIFICATIONS.PDF
PCI PXI PCIE 6509 USER GUIDE AND SPECIFICATIONS.PDF
SCB-100 100A LETTER OF VOLATILITY.PDF
Why Buy From Apex Waves:
"The business transaction was super easy and friendly."
"Hand carrying parts to fedex directly to make sure I get them overnight. Great service"
"They were very helpful to get me the test equipment that I need."
SCB-100
Modular Systems > National Instruments > Accessories
1-800-915-6216
- Description
- Technical Specifications
- FAQ
- Manuals & PDFs
National Instruments SCB-100 Shielded Connector Block
The SCB-100 (Part Number: 776990-01, 182788C-01) is a Shielded Connector Block. This Connector Block is designed to provide easy cabling between 100-pin digital I/O devices and I/O signals. The NI SCB-100 offers maximum protection from noise corruption since it is a shielded accessory with a reference temperature sensor. It has 100 screw terminals, and a strain relief bar.
The following are needed to use the SCB-100:
· 100-pin DAQ device and device documentation,
· SH100100 cable for E Series/MIO devices or SH100-100-F cable for DIO/TIO Series devices,
· ≤26 AWG wire,
· And other equipment which can be found in the installation guide.
This Shielded Connector Block is designed for E Series MIO devices (NI 6025E, 6031E, 6071E and 6033E), DIO devices (NI 6511, 6508, PCI-DIO-96, 6509, 6512, 6514, 6513, 6527, 6515 etc.), and devices from the TIO Series like NI 6624. Moreover, the NI SCB-100 can be used with various other products that come with a 100-pin male 0.050 series shielded D-type I/O connector. The temperature sensor incorporated in this Connector Block can accommodate a broad range of thermocouple models. With the SCB-100, you can measure thermocouples in single-ended or differential configurations.
This National Instruments SCB-100 Shielded Connector Block offers low-noise signal termination when it is used with shielded cables. Low noise termination is important for digital signal transmission systems. The NI SCB-100 comes equipped with 3 general purpose breadboard areas. This Connector Block comes equipped with chassis ground terminals that can be used for grounding high-impedance sources. The cold-junction sensor can provide an output of 10 mV/°C with ±0.5 °C accuracy. In typical operating conditions, the NI SCB-100 should draw no more than 10 mA of current at +5 VDC. The NI device weighs 15.6 oz, and measures 7.7 x 6.0 x 1.8 in. in physical dimensions. The device has a component operating temperature range of 0 to 70 °C, a storage temperature range of –55 to 125 °C, and a noncondensing operating and storage humidity range of 5% to 90% and 5% to 90% respectively.
SCB-100 Obsolete Status has been announced by National Instruments, but the Connector Block will still be available for purchase and repairs by Apex Waves.
Model | SCB-100 |
---|---|
Manufacturer | National Instruments |
Part Number | 776990-01, 182788C-01 |
Type | Shielded Connector Block |
Screw Terminals | 101 |
Cold-Junction Sensor Accuracy | ±0.5 °C |
Cold-Junction Sensor Output | 10 mV/°C |
I/O Connectors | One 100-pin male 0.050 series shielded D-type connector |
Dimensions | 7.7 by 6.0 by 1.8 in. |
Weight | 1 lb 15.6 oz. |
Warranty | Three Year Warranty |
SCB-100 Manual | User Manual and Maintenance Manual Available for Download |
Price | Contact a sales representative for a quote. |
National Instruments SCB-100 Frequently Asked Questions
Question: What are the switch settings for the SCB-100?
Answer: Before you can connect an IMAQ D100100 cable to an IMAQ SCB-100 connector block, the switch settings on the IMAQ SCB-100 must be changed to the generic screw terminals switch configuration.
Question: How many screw terminals does the SCB-100 use?
Answer: The SCB-100 has 101 screw terminals, including one no-connect terminal. There are all I/O signals available at the terminals.
Question: At what temperature should the SCB-100 component be operated?
Answer: The operating environment temperature of the SCB-100 ranges from 0 - 70 degrees celsius.
SCB-100 PDF Manuals & Diagrams
SCB-100 PDF Manuals
ARCHIVED IMAQ D100100 CABLE INSTALLATION GUIDE.PDF
ARCHIVED LOOKOUT 3.7 ADDENDUM.PDF
ARCHIVED LOOKOUT OBJECT REFERENCE MANUAL.PDF
ARCHIVED LOOKOUT REFERENCE MANUAL.PDF
IMAQ SCB-100 CONNECTOR BLOCK AND IMAQ D100100 CABLE.PDF
NI 60XX 60XXE PINOUT LABELS FOR THE SCB-100 NOTE TO USERS.PDF
NI 6528 6529 USER GUIDE AND SPECIFICATIONS.PDF
NI 65XX PINOUT LABELS FOR THE SCB-100 NOTE TO USERS.PDF
NI 6624 CALIBRATION PROCEDURE.PDF
NI 66XX PINOUT LABELS FOR THE SCB-100 NOTE TO USERS.PDF
NI USB 6509 USER GUIDE AND SPECIFICATIONS.PDF
PCI PXI PCIE 6509 USER GUIDE AND SPECIFICATIONS.PDF
SCB-100 100A LETTER OF VOLATILITY.PDF
Why Buy From Apex Waves
"The business transaction was super easy and friendly."
"Hand carrying parts to fedex directly to make sure I get them overnight. Great service"
"They were very helpful to get me the test equipment that I need."